<![CDATA[M5 PoECAM-W Stream help]]>Hello,

I've connected my M5 PoECAM-W to the switch, and I am seeing the led lights for the network connection properly. But I am unable to access the steam via {ip}/steam

Do I need to use the ESP32 burner to upload the software? Is there no wat to access the feed without doing this?

]]>https://community.m5stack.com/topic/6365/m5-poecam-w-stream-helpRSS for NodeMon, 20 Apr 2026 03:01:22 GMTMon, 22 Apr 2024 17:14:49 GMT60<![CDATA[Reply to M5 PoECAM-W Stream help on Fri, 26 Apr 2024 08:36:22 GMT]]>@mikecre said in M5 PoECAM-W Stream help:

Do i need to use the piece?

There is nothing magic about the small extra board. it should be same if you connected your jump wires like this:

0_1714120436731_1ab3c7b3-0c83-4cfb-84e6-a49a963caf4b-Untitled Diagram.jpg

]]>https://community.m5stack.com/post/24947https://community.m5stack.com/post/24947Fri, 26 Apr 2024 08:36:22 GMT<![CDATA[Reply to M5 PoECAM-W Stream help on Thu, 25 Apr 2024 20:21:28 GMT]]>I was able to get it working using the piece. I'm not sure how the the way this comes really makes it easy... couldn't that board just come pre soldered on? Instructions could def be much more clear imho but i'm also a newbie to these types of devices.

]]>https://community.m5stack.com/post/24940https://community.m5stack.com/post/24940Thu, 25 Apr 2024 20:21:28 GMT<![CDATA[Reply to M5 PoECAM-W Stream help on Thu, 25 Apr 2024 20:01:05 GMT]]>I tried all the baud ratings, I did not connect like that I used the cables as I didn't want to solder. Do i need to use the piece?

]]>https://community.m5stack.com/post/24939https://community.m5stack.com/post/24939Thu, 25 Apr 2024 20:01:05 GMT<![CDATA[Reply to M5 PoECAM-W Stream help on Thu, 25 Apr 2024 14:40:35 GMT]]>And sometimes you need to lower the baud rate when burning:

0_1714056028495_0dcb9012-62f9-4719-adbb-d875e91b2a66-image.png

]]>https://community.m5stack.com/post/24937https://community.m5stack.com/post/24937Thu, 25 Apr 2024 14:40:35 GMT<![CDATA[Reply to M5 PoECAM-W Stream help on Thu, 25 Apr 2024 14:30:32 GMT]]>Assembled and connected like this?

0_1714055424296_61121405-cf99-400a-ae7c-076136135ef8-P_20240425_162028.jpg

]]>https://community.m5stack.com/post/24936https://community.m5stack.com/post/24936Thu, 25 Apr 2024 14:30:32 GMT<![CDATA[Reply to M5 PoECAM-W Stream help on Thu, 25 Apr 2024 14:02:15 GMT]]>I have bought the burner, but I keep getting this error:
A fatal error occurred: Failed to connect to Espressif device: No serial data received.

It is detecting the com port when I connect and disconnect... I have tried with the Easyloader, the m5 burner app and the arduino ide

]]>https://community.m5stack.com/post/24935https://community.m5stack.com/post/24935Thu, 25 Apr 2024 14:02:15 GMT<![CDATA[Reply to M5 PoECAM-W Stream help on Tue, 23 Apr 2024 08:06:44 GMT]]>if you have this firmware burned:
0_1713854967340_5c9ab69e-7cdb-43c1-b5e5-43652496a0ce-image.png

You should be able to get the video stream on http://<Cam-IP> or http://<Cam-IP>/stream
This firmware is setup by default to ask for an IP on DHCP.

Since there is no USB port you'll need a small adapter like this to burn the firmware on to the PoECAM.

]]>https://community.m5stack.com/post/24913https://community.m5stack.com/post/24913Tue, 23 Apr 2024 08:06:44 GMT