M5StickC: turn off screen completely

ws1088

@dda Thanks! @ricardocosta can probably check to see how much current is used when backlight is off.

dda

While I'm at it, an explanation about M5.Axp.ScreenBreath(x);. The code is:

void AXP192::ScreenBreath(uint8_t brightness) {
  Wire1.beginTransmission(0x34);
  Wire1.write(0x28);
  Wire1.write(((brightness & 0x0f) << 4)); //Enable LDO2&LDO3, LED&TFT 3.3V
  Wire1.endTransmission();
}

What it does is it takes the value you passed, cuts it to 4 bits (0-15) and moves those 4 bits to bits 4-7. Register 28H is voltage control for LDO2 (bits 4-7) and LDO3 (bits 0-3). So the OLED is connected to LDO2.

What that 0-15 value represents is a voltage of 1.8 to 3.3V, in 100mV/steps. So M5.Axp.ScreenBreath(0); sets voltage to 1.8V, and M5.Axp.ScreenBreath(15); to 3.3V. Not what we really want – as the goal was to set voltage to zero... :-)

0_1564416322717_e7e8bf46-cea3-41c2-bed7-1869e4cb9146-image.png

Whereas register 12H controls the state (ON/OFF) of a bunch of wires, including LDO2 (bit 2). Hence the code above.

0_1564416423649_0222b6b2-3ed3-473a-9669-0020509cb215-image.png

ws1088

Does your code cut the voltage to the backlight only? or to the screen as well?

dda

To be tested but I think this turns off OLED_VDD, ie the current to the OLED. Register 10H is said to be for OLED_VPP so setting it to zero could help too.

dda

I did a simple test: with only REG 28H the screen stays slightly warm. With both 28H and 10H, the screen cools off after a while. Hardly a scientific test, I know, but seems to point to the need to set both registers.

ws1088

@dda what a wonderful work you have done! I hope this will enable @Multihelix to use M5StickC as a watch (turn off OLED after a timeout and turn on OLED on button press or accelerometer)

maxstack

@multihelix

How are you getting 5 hours of life? it seems you would need <16 ma total drain

Are you sleeping the ESP32?

dda

@ws1088 Funny enough I bought my M5StickC with the watch strap and all, but not because I wanted a watch – I don't wear them – but because it enables me to tie it up to my backpack when I do LoRa range tests :-)

ws1088

@dda said in M5StickC: turn off screen completely:

@ws1088 Funny enough I bought my M5StickC with the watch strap and all, but not because I wanted a watch – I don't wear them – but because it enables me to tie it up to my backpack when I do LoRa range tests :-)

why would you use m5stickc to do LoRa range tests? You can get LoRa chip with OLED screen. Do you connect m5stickc to a LoRa chip via I2C? or WiFi AP?

dda

I have a lot of different LoRa chips and setups. I have one board, at 230 MHz, that I can connect through the hat connector (I need 3 pins + Vcc/GND). I have transceivers, both at 230 and 433 MHz, I connect to via RS485 (I bought a hat for that, and also some RS485 for my M5Stack cores). etc etc. The smaller the better :-)

Multihelix

@maxstack - Yes, I used ESP DeepSleep set to wake on Button A being pressed, but I would say that the 5 hour time was not under ideal conditions, as I occasionally woke up the device to confirm it was still working and to check the time - a resonable activity for a watch.

spiffmonious

@multihelix Can you post a link to your watch code?

klimbot

@dda said in M5StickC: turn off screen completely:

I did a simple test: with only REG 28H the screen stays slightly warm. With both 28H and 10H, the screen cools off after a while. Hardly a scientific test, I know, but seems to point to the need to set both registers.

I'm looking at this thread to hopefully implement a complete screen turn off, but am not sure what register mask to use (based on quoted post)

Here is what I have, the screen is off but hard to know if the screen has actually been disabled.

void turnOffScreen() {
Wire1.beginTransmission(0x34);
Wire1.write(0x10);
Wire1.write(0b00000000); // 7-3=? | 2=EXTEN | 1=? | 0=DC-DC2
Wire1.endTransmission();

Wire1.beginTransmission(0x34);
Wire1.write(0x28);
Wire1.write(0b00001111); // 7-4=LDO2 | 3-0=LDO3
Wire1.endTransmission();
}

ForestRupicolous

@klimbot: I think you have to turn LDO3 and LDO2 off, in your code only LDO2 is off. Take a look at this picture: https://docs.m5stack.com/assets/img/product_pics/core/minicore/m5stickc/m5stickc_05.webp

viandou

This is how I init my M5StickC in a full black screen way.

M5.begin(0,1,1);
M5.Axp.SetLDO2(false);
M5.Axp.SetLDO3(false);