UIFlow digital input interrupt

[birdsong]

In UIFlow is it possible to use an interrupt on an input? when I get a sub millisecond low signal on an input I would like to run some code.

[lukasmaximus]

When you say sub millisecond I guess you are not going to use a button to interrupt, if so then how do you intend to interrupt from an input

[birdsong]

50hz triac phase control with zero crossing timing synchronization. 100micro second timing tolerance or better. I ended up porting to Arduino/C++, too many limitations with UIFlow for now, python maybe to slow anyway. UIFlow is a good tool for higher level/basic control.

[Gaviota]

Hello,
try an execute block, look at my code below.

First i defined the two variables "is_running" and "counter".
In UIFlow i defined pin0 with GPIO26 as input with pull down resistor.!
Then i defined the event_interrupt(pin) - procedure. I use it for counting impulses at the GPIO26, therefore it is necessary to declare the variables as globals.

Every second i read in the main loop the value of the counter variable and reset the is_running variable.

def event_interrupt(pin):
global is_running, counter
is_running = True
counter += 1

pin0.irq(trigger=machine.Pin.IRQ_RISING, handler=event_interrupt)

[Schubi]

@Gaviota
hello and thank you for your information.
Would you be so kind to post the full code?
It doesn't work for me - i always get a syntax error.

Thanks in advance,

Schubi

[Schubi]

@Gaviota
Hello Gaviota,
thank you for sharing this information.

I tried to implement it, but i get an error.
Would you be so kind to post the whole program?

Thank you in advance,

Schubi

[Schubi]

@Gaviota
hello Gaviota,
i tried to run your code, but i always get an error.
Would you be so kind to post the full program so i can find my mistake.

Thank yo in advance,
Schubi

[BT99]

@Gaviota post was helpful to me. Thanks.
Below is an example of a N/O button interrupt, connected between G26 and GND.
Counter increments multiple times per button push.
This shows that software debounce could be necessary in many cases.
Cheers - BillT

[LyleDodge]

I've created a custom module to avoid the need to use the "Execute" block. It basically gives you a way to set the pin number, trigger, and callback for the IRQ. You will still create your own function using Blockly.

1. Create a Variable: example "counter"
2. Create a Function:
   1. Name it what you like, example: "count_pulses"
   2. Add single step from Variables: change counter by 1
3. Init PWM0 with your desired pin, freq, and duty
4. Load the attached file under Custom | Open *.m5b file
5. Drag "PIN_IRQ" from Custom onto your workspace
   1. Set the pin number (just an integer, 0 for example)
   2. Set your trigger "machine.Pin.IRQ_RISING"
   3. Set the handler to your function from step 2 above "count_pulses"
6. Add a label if you want and set the loop event to update a label with the current counter value
7. It sounds more complicated than it actually is, check the screenshot

Your resulting code should look vaguely like this:

from m5stack import *
from m5ui import *
from uiflow import *
import machine

setScreenColor(0x222222)

counter = None

label0 = M5TextBox(146, 187, "Text", lcd.FONT_Default, 0xFFFFFF, rotate=0)

from numbers import Number

def count_pulses():
  global counter
  counter = (counter if isinstance(counter, Number) else 0) + 1

PWM0 = machine.PWM(26, freq=25000, duty=50, timer=0)
pin0.irq(trigger=machine.Pin.IRQ_RISING, handler=count_pulses)
while True:
  label0.setText(str(counter))
  wait_ms(2)

Have fun storming the castle!

[Doswiadczalnik]

@lyledodge I can’t see attached file. Is there any or it problem with my iPhone?