UIFlow doesn't start on new Core2

guillaumelf26

I just received my first Core2 yesterday, and I had the same problem trying to run the uiFlow 1.7.1 firmware.

After many attempts, I finally tried the 1.7.0 version, and it worked ! Maybe try this version instead of the latest one.

felmue

Hello @puzznic

after burning UIFlow, what do you see in the COM Monitor log of M5Burner when you reset M5Core2? Any errors?

Thanks
Felix

NetworkUke

I'm running into the same issue. Right after

"Hard resetting via RTS pin...

Burn Successfully"

The m5stack display freezes and in the console output is:

rst:0x10 (RTCWDT_RTC_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
invalid header: 0x4f44213c
invalid header: 0x4f44213c
invalid header: 0x4f44213c
invalid header: 0x4f44213c
invalid header: 0x4f44213c
invalid header: 0x4f44213c
invalid header: 0x4f44213c
invalid header: 0x4f44213c
ets Jul 29 2019 12:21:46

on an infinite loop.

Even after re-burning it with the easy loader when I attempt to burn UIFlow_Core2 the same issue occurs. Any advice is greatly appreciated.

felmue

Hi guys

@NetworkUke : please see your other post. In your case the firmware file size is way to small.

@puzznic : have you tried to reduce the baudrate? Not sure that will help but worth a try.

Thanks
Felix

inasawa

It seems to be the same situation as the Core 2 I bought yesterday.
Core2FactoryTest and draw_by_touch work fine, but UIFlow_Core2 v1.7.1.1-core2 (I also tried v1.7.0 / v1.7.1) doesn't work.

However, it seems running with black screen. I tried connect to Core2 from UIFlow Cloud and run the program. print() can print text to the serial console, but M5Label will show nothing on the Core2 screen. just black screen.

I tried burn with low baudrate (115200), but nothing changed

inasawa

Since UIFlow display nothing on the screen, I tried the test with the ILI9341 library for MicroPython I found.
https://github.com/tuupola/micropython-ili934x/blob/master/ili934x.py

I copied the above library to Core2 and ran the following code from the serial console.

import ili934x
from machine import Pin, SPI
spi = SPI(miso=Pin(38), mosi=Pin(23, Pin.OUT), sck=Pin(18, Pin.OUT))
display = ili934x.ILI9341(spi, cs=Pin(5), dc=Pin(15), rst=Pin(4))
display.fill(ili934x.color565(0xff, 0x11, 0x22))
display.pixel(120, 160, 0)
display.print('1234567890 ABCDEFGHIJKLMNOPQRSTUVWXYZ')
     :     :     :
display.print('1234567890 ABCDEFGHIJKLMNOPQRSTUVWXYZ')

As a result, the characters are displayed as shown in the image below.
I'm not sure what this means, but can it help analyze the problem?

OffLineR

I had the same problem.
Core2 did not turn on after 1.7.1.1
Currently I am using 1.7.0 instead.

inasawa

I don't know what happened. Core2 that has not been displayed with UIFlow for 2 days since I bought it, suddenly, yes suddenly, when I reset Core2, something was displayed, and every time I reset it, the display was distorted or displayed upside down. After several resets, the display is now showing normally.

I feel that there is an unstable part in the display-related HW. Firmware is UIFlow_Core2-v1.7.1.1-core2.bin.

inasawa

It seems that it was a short-lived joy. Revert to a black screen, distorted screen, or an upside-down screen.
I tried v1.7.1.1, v1.7.1, v1.7.0, v1.6.6 and they are all the same and have a black screen.
It's HW problem?

Also, even in this situation with UIFlow is running, if I burn factory test firmware, it will work normally.

inasawa

After struggling for a while, I had this Core2 replaced at the shop where I bought it as an initial defect.
I'm not sure, but it seems that the display mechanism in Arduino and the display mechanism in UIFlow are different, and even if Factory Test works normally, it may not work properly in UIFlow.