🤖Have you ever tried Chat.M5Stack.com before asking??😎
    M5Stack Community
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    • Register
    • Login

    Atom DTU NB-IoT2 issues.

    Modules
    2
    18
    1.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • cocoaC
      cocoa
      last edited by

      I list a number of issues I'm experiencing with the new NB-IOT2 module.

      Tests were done on two Atom DTU modules, both showing the same issues.

      1. The serial port of the Simcom 7028 NB-IoT module becomes unresponsive, that is, it accepts commands but does not respond.

      2. The examples provided for Arduino do not work (http, mqtt etc)

      3. GPIO Hardware Errors

      4. A reset pin that does not exist is defined

      
#define ATOM_DTU_SIM7028_EN 12 // ?? Atom S3 has not G12 !!

      and

      #define ATOM_DTU_SIM7028_RESET -1   // ?? what reset it performs ?

      So it is not clear how to reset the Simcom SIM7028 modem.

      1. When trying to run the http example, the modem goes into search mode and no longer returns. From now on, it is no longer possible to access the modem.

      2. There is no schematic of the Atom S3 Lite module, only the pinout.

      3. M5burner does not register the Atom S3 module and UIFlow2 does not work on macOS.

      It would be really great if M5Stack engineers tried testing on macOS (Apple Silicon) and published an how-to.

      Thx All

      felmueF 1 Reply Last reply Reply Quote 0
      • felmueF
        felmue @cocoa
        last edited by felmue

        Hello @cocoa

        • What kind of SIM card are you using? In my experience the SIM card needs to be a NB-IoT specific one. For me SIM cards used in mobile phone didn't work.

        • If your SIM card uses a PIN then you either need to remove it or modify the code to use the correct PIN.

        • Care to share you log when you run the http example?

        Some answers to your questions:

        Re 1: Hmm, I don't see that.

        Re 2: I've just tested the http example and it works for me.

        Re 3: I see that too, but they don't seem to hurt.

        Re 4: the Reset pin of the SIM7028 is not connected (see schematic), that is way it's set to -1 I guess.

        Re 5: what do you mean by search mode?

        Re 6: yes, that is correct.

        Re 7: I cannot comment on M5Burner and macOS. I don't have a Apple Silicon one.

        Thanks
        Felix

        GPIO translation table M5Stack / M5Core2
        Information about various M5Stack products.
        Code examples

        cocoaC 1 Reply Last reply Reply Quote 0
        • cocoaC
          cocoa @felmue
          last edited by

          @felmue Hello,

          Sim is 1NCE NB-IoT Sim.
          It is connected to the Vodafone BTS, it is 'online'.

          The error I'm receiving from http example ATOM_DTU_NB2_PIO 

          Reconnecting to /dev/cu.usbmodem1101 .
Please build project in debug configuration to get more details about an exception.
See https://docs.platformio.org/page/projectconf/build_configurations.html


         Connected!
18:07:02.791 > >>ATOM DTU NB HTTP TEST
18:07:02.791 > CCID: 
18:07:03.791 > Signal quality: 99
18:07:03.791 > Initializing modem...
18:07:03.791 > [  2679][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:07:03.797 > E (2571) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:04.098 > E (2872) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:19.298 > waiting....15s
18:07:19.298 > [ 18186][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:07:19.304 > E (18078) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:19.604 > E (18378) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:34.804 > waiting....31s
18:07:34.804 > [ 33692][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:07:34.810 > E (33584) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:35.110 > E (33884) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:50.310 > waiting....46s
18:07:50.310 > [ 49198][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:07:50.316 > E (49090) gpio: gpio_set_level(227): GPIO output gpio_num error
18:07:50.616 > E (49390) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:05.816 > waiting....62s
18:08:05.816 > [ 64704][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:08:05.822 > E (64596) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:06.122 > E (64896) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:21.322 > waiting....77s
18:08:21.322 > [ 80210][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:08:21.328 > E (80102) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:21.629 > E (80403) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:36.828 > waiting....93s
18:08:36.829 > [ 95717][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:08:36.835 > E (95609) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:37.135 > E (95909) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:52.334 > waiting....108s
18:08:52.335 > [111223][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:08:52.341 > E (111115) gpio: gpio_set_level(227): GPIO output gpio_num error
18:08:52.641 > E (111415) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:07.840 > waiting....124s
18:09:07.841 > [126729][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:09:07.847 > E (126621) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:08.146 > E (126921) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:23.346 > waiting....139s
18:09:23.347 > [142235][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:09:23.353 > E (142127) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:23.652 > E (142427) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:38.852 > waiting....155s
18:09:38.853 > [157741][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:09:38.858 > E (157633) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:39.158 > E (157933) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:54.358 > waiting....170s
18:09:54.358 > [173247][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:09:54.365 > E (173139) gpio: gpio_set_level(227): GPIO output gpio_num error
18:09:54.664 > E (173439) gpio: gpio_set_level(227): GPIO output gpio_num error
18:10:09.864 > waiting....186s
18:10:09.864 > [188753][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
18:10:09.870 > E (188645) gpio: gpio_set_level(227): GPIO output gpio_num error
18:10:10.170 > E (188945) gpio: gpio_set_level(227): GPIO output gpio_num error
          felmueF 1 Reply Last reply Reply Quote 0
          • felmueF
            felmue @cocoa
            last edited by

            Hi @cocoa

            1NCE SIM is what I am using too.

            Signal quality: 99 is not so good. Should be lower than 99.

            Try un-commenting #define DUMP_AT_COMMANDS at the top of the sketch. This should give you more information about what's happening/going wrong.

            BTW: I get log output similar to yours if no SIM card is installed. Maybe double-check the SIM card is inserted correctly?

            Thanks
            Felix

            GPIO translation table M5Stack / M5Core2
            Information about various M5Stack products.
            Code examples

            cocoaC 1 Reply Last reply Reply Quote 0
            • cocoaC
              cocoa @felmue
              last edited by

              @felmue Hi,

              The strange thing is that the blue led no longer flashes after three or four blinks.

              If I use MicroPython I can send AT commands to the modem, read the CSQ (actual value is 29), request the resolution of an FQDN etc...

              So the sim is OK, it's connected and modem communicate with BTS.

              When I use Arduino libraries the module stop to works.

              Do you have a program in Platformio/Arduino that you know definitely works and it's able to connect to an http server?

              Thank you.

              felmueF 1 Reply Last reply Reply Quote 0
              • felmueF
                felmue @cocoa
                last edited by felmue

                Hello @cocoa

                I was confused about the blue LED too. It seems that the blue LED blinks fast while searching for a provider, is off when connected to a provider and then occasionally blinks slow when transferring data.

                I forgot that I modified TinyGSM library in the past, when I first tried the SIM7028 examples. Sorry about that.

                In my case AT+CREG? returns +CREG: 0,7 which means registered for SMS only roaming. Unfortunately TinyGSM library doesn't check for that. It only accepts 1, 5 and 6 (registered home, registered roaming, sms only home). See here. I think that might be an error in SIM7028 firmware.

                Anyways, you can fix that by allowing 7 as an OK result as well or as I did it: I modified a line above to check for AT+CEREG? instead, which properly returns +CEREG: 0,5, e.g. registered roaming. See here. Just change CREG to CEREG like below:

                //        return (RegStatus)getRegistrationStatusXREG("CREG"); 
        return (RegStatus)getRegistrationStatusXREG("CEREG");

                Thanks
                Felix

                GPIO translation table M5Stack / M5Core2
                Information about various M5Stack products.
                Code examples

                cocoaC 1 Reply Last reply Reply Quote 0
                • cocoaC
                  cocoa @felmue
                  last edited by

                  @felmue Hi, thanks for the indications, I'll check and let you know.

                  Do you know how it is possible to reset or reboot the SIM7028 from the S3 Lite atom?

                  If the Atom DTU modem is stuck and isn't possible to switch power off and on (typical scenario of every IoT device that is placed in remote zones or that cannot be accessed) in which way Atom DTU can be back to an operating condition?

                  I ask these questions because I don't understand why the modem control pin was not connected to an Atom I/O.

                  Thank you.

                  felmueF 1 Reply Last reply Reply Quote 0
                  • felmueF
                    felmue @cocoa
                    last edited by felmue

                    Hello @cocoa

                    no, it is not possible to reset/reboot SIM7028 from M5AtomS3 due to the fact that RESET pin is not connected.

                    There is an AT command to reset SIM7028, but if it is stuck that probably doesn't work. The other way is pulling RESET pin low, but that doesn't help as long as RESET pin isn't connected.

                    If you don't need the built-in RS485 or the built-in Groove port you could rewire one of those GPIOs via transistor to the RESET pin. (But make sure you use the appropriate circuit / level shifter.)

                    From SIM7028 Hardware Design document:

                    "3.2.1 Power on
                    The module is automatically turned on after power on, without a power button. Under the condition that the RESET pin is not pulled low by the outside, the module will automatically power on after supplying a voltage of 2.2V to 4.3V to the VBAT pin."

                    "3.2.2 Power off
                    The module can be shut down by disconnecting the VBAT power supply."

                    "3.2.3 Reset Function
                    SIM7028 can reset the module by keeping the RESET pin low for at least 50ms. The module can also be reset by the AT command "AT+NRB".
                    The RESET signal has been pulled up inside the chip, and the RESET signal will immediately change to a high level after the module is powered on."

                    Edit: I just tried the AT command to reset the module, but all I get back is ERROR and nothing happens.

                    Thanks
                    Felix

                    GPIO translation table M5Stack / M5Core2
                    Information about various M5Stack products.
                    Code examples

                    cocoaC 1 Reply Last reply Reply Quote 0
                    • cocoaC
                      cocoa @felmue
                      last edited by

                      Hello @felmue ,

                      Thank you for informations and suggestions.

                      For me it is clear that the module must be used as a product and sold, so I hope that the AT reset command will solve any stuck of the modem.

                      M5stack has not yet released the examples in UIFLOW2 for this module, so the module is useless for those who want to use UIFlow2. The ones for Atom DTU UIFlow1 obviously don't work.

                      I just can't use it with Arduino / Platformio too.

                      Could you share your source code to make a http connection? It would be of great help to me to get out of this impasse.

                      Thx.

                      felmueF 1 Reply Last reply Reply Quote 0
                      • felmueF
                        felmue @cocoa
                        last edited by felmue

                        Hello @cocoa

                        the http example from here is working for me with the one modification in TinyGSM I mentioned.

                        You haven't shared the log with #define DUMP_AT_COMMANDS enabled - this might shed some light onto what going on at your end.

                        I guess you haven't noticed my edited note above about the AT reset command AT+NRB which did not work for me. All I got was an ERROR.

                        Here you can find my modification to reset SIM7028 via GPIO.

                        BTW: have you ever tried to check the firmware version currently installed on your SIM7028? E.g. AT+CGMR? Maybe it needs an upgrade?

                        Thanks
                        Felix

                        GPIO translation table M5Stack / M5Core2
                        Information about various M5Stack products.
                        Code examples

                        cocoaC 1 Reply Last reply Reply Quote 0
                        • cocoaC
                          cocoa @felmue
                          last edited by

                          Hi @felmue, sorry for delay.

                          Here is the log with #define DUMP_AT_COMMANDS enabled .

                          

         Connected!
14:23:54.308 > >>ATOM DTU NB MQTT TEST
14:23:54.308 > AT+CICCID
14:23:54.308 > 
14:23:54.308 > ERROR
14:23:54.308 > CCID: ERROR
14:23:54.308 > AT+CSQ
14:23:54.314 > 
14:23:54.314 > +CSQ: 21,0
14:23:54.314 > 
14:23:54.315 > OK
14:23:54.315 > Signal quality: 21
14:23:54.315 > Initializing modem...
14:23:54.315 > [  1689][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
14:23:54.321 > E (1581) gpio: gpio_set_level(227): GPIO output gpio_num error
14:23:54.621 > E (1881) gpio: gpio_set_level(227): GPIO output gpio_num error
14:23:59.621 > AT
14:23:59.624 > 
14:23:59.624 > OK
14:23:59.624 > ATE0
14:23:59.628 > 
14:23:59.629 > OK
14:23:59.629 > AT+CFUN=1
14:23:59.636 > 
14:23:59.636 > OK
14:23:59.636 > AT+QCLEDMODE=1
14:23:59.641 > 
14:23:59.641 > OK
14:23:59.641 > AT+CMEE=0
14:23:59.645 > 
14:23:59.645 > OK
14:23:59.645 > AT+CTZR=0
14:23:59.649 > 
14:23:59.649 > OK
14:23:59.649 > AT+CTZU=1
14:23:59.653 > 
14:23:59.653 > OK
14:23:59.653 > AT+CPIN?
14:23:59.660 > 
14:23:59.660 > +CPIN: READY
14:23:59.661 > 
14:23:59.661 > OK
14:23:59.661 > Waiting for network...
14:23:59.661 > AT+CREG?
14:23:59.667 > 
14:23:59.667 > +CREG: 0,0
14:23:59.668 > 
14:23:59.668 > OK
14:23:59.918 > AT+CREG?
14:23:59.924 > 
14:23:59.925 > +CREG: 0,0
14:23:59.925 > 
14:23:59.925 > OK
14:24:00.175 > AT+CREG?
14:24:00.181 > 
14:24:00.181 > +CREG: 0,0
14:24:00.182 > 
14:24:00.182 > OK
14:24:00.432 > AT+CREG?
14:24:00.438 > 
14:24:00.439 > +CREG: 0,0
14:24:00.439 > 
14:24:00.439 > OK
14:24:00.689 > AT+CREG?
14:24:00.694 > 
14:24:00.695 > +CREG: 0,0
14:24:00.695 > 
14:24:00.695 > OK
14:24:00.946 > AT+CREG?
14:24:00.952 > 
14:24:00.952 > +CREG: 0,0
14:24:00.952 > 
14:24:00.952 > OK
14:24:01.203 > AT+CREG?
14:24:01.209 > 
14:24:01.209 > +CREG: 0,0
14:24:01.209 > 
14:24:01.210 > OK
14:24:01.460 > AT+CREG?
14:24:01.466 > 
14:24:01.466 > +CREG: 0,0
14:24:01.467 > 
14:24:01.467 > OK
14:24:01.717 > AT+CREG?
14:24:01.723 > 
14:24:01.724 > +CREG: 0,0
14:24:01.724 > 
14:24:01.724 > OK
14:24:01.974 > AT+CREG?
14:24:01.980 > 
14:24:01.980 > +CREG: 0,0
14:24:01.981 > 
14:24:01.981 > OK
14:24:02.231 > AT+CREG?
14:24:02.237 > 
14:24:02.238 > +CREG: 0,0
14:24:02.238 > 
14:24:02.238 > OK
14:24:02.488 > AT+CREG?
14:24:02.494 > 
14:24:02.494 > +CREG: 0,0
14:24:02.494 > 
14:24:02.495 > OK
14:24:02.745 > AT+CREG?
14:24:02.751 > 
14:24:02.751 > +CREG: 0,0
14:24:02.751 > 
14:24:02.751 > OK
14:24:03.002 > AT+CREG?
14:24:03.008 > 
14:24:03.008 > +CREG: 0,0
14:24:03.009 > 
14:24:03.009 > OK
14:24:03.259 > AT+CREG?
14:24:03.264 > 
14:24:03.265 > +CREG: 0,0
14:24:03.265 > 
14:24:03.265 > OK
14:24:03.516 > AT+CREG?
14:24:03.521 > 
14:24:03.521 > +CREG: 0,0
14:24:03.522 > 
14:24:03.522 > OK
14:24:03.773 > AT+CREG?
14:24:03.779 > 
14:24:03.779 > +CREG: 0,0
14:24:03.779 > 
14:24:03.779 > OK
14:24:04.030 > AT+CREG?
14:24:04.036 > 
14:24:04.036 > +CREG: 0,0
14:24:04.036 > 
14:24:04.036 > OK
14:24:04.287 > AT+CREG?
14:24:04.293 > 
14:24:04.293 > +CREG: 0,0
14:24:04.293 > 
14:24:04.293 > OK
14:24:04.544 > AT+CREG?
14:24:04.549 > 
14:24:04.549 > +CREG: 0,0
14:24:04.550 > 
14:24:04.550 > OK
14:24:04.801 > AT+CREG?
14:24:04.806 > 
14:24:04.806 > +CREG: 0,0
14:24:04.807 > 
14:24:04.807 > OK
14:24:05.058 > AT+CREG?
14:24:05.064 > 
14:24:05.064 > +CREG: 0,0
14:24:05.064 > 
14:24:05.065 > OK
14:24:05.315 > AT+CREG?
14:24:05.321 > 
14:24:05.322 > +CREG: 0,0
14:24:05.322 > 
14:24:05.322 > OK
14:24:05.572 > AT+CREG?
14:24:05.578 > 
14:24:05.578 > +CREG: 0,0
14:24:05.580 > 
14:24:05.580 > OK
14:24:05.829 > AT+CREG?
14:24:05.835 > 
14:24:05.835 > +CREG: 0,0
14:24:05.835 > 
14:24:05.836 > OK
14:24:06.086 > AT+CREG?
14:24:06.091 > 
14:24:06.092 > +CREG: 0,0
14:24:06.092 > 
14:24:06.092 > OK
14:24:06.343 > AT+CREG?
14:24:06.349 > 
14:24:06.349 > +CREG: 0,0
14:24:06.349 > 
14:24:06.350 > OK
14:24:06.600 > AT+CREG?
14:24:06.606 > 
14:24:06.606 > +CREG: 0,0
14:24:06.607 > 
14:24:06.607 > OK
14:24:06.857 > AT+CREG?
14:24:06.863 > 
14:24:06.863 > +CREG: 0,0
14:24:06.864 > 
14:24:06.864 > OK
14:24:07.114 > AT+CREG?
14:24:07.120 > 
14:24:07.121 > +CREG: 0,0
14:24:07.121 > 
14:24:07.121 > OK
14:24:07.371 > AT+CREG?
14:24:07.377 > 
14:24:07.377 > +CREG: 0,0
14:24:07.378 > 
14:24:07.378 > OK
14:24:07.628 > AT+CREG?
14:24:07.634 > 
14:24:07.634 > +CREG: 0,0
14:24:07.635 > 
14:24:07.635 > OK
14:24:07.885 > AT+CREG?
14:24:07.890 > 
14:24:07.891 > +CREG: 0,0
14:24:07.891 > 
14:24:07.892 > OK
14:24:08.142 > AT+CREG?
14:24:08.147 > 
14:24:08.147 > +CREG: 0,0
14:24:08.148 > 
14:24:08.148 > OK
14:24:08.399 > AT+CREG?
14:24:08.404 > 
14:24:08.404 > +CREG: 0,0
                          felmueF 1 Reply Last reply Reply Quote 0
                          • felmueF
                            felmue @cocoa
                            last edited by felmue

                            Hello @cocoa

                            from the output +CREG: 0,0 it looks like your modem is not registered to the network. According to the AT commands documentation, the second 0 in that answer means:

                            0 not registered, MT is not currently searching for an operator to register to

                            You could try to manually issue a 'AT+CEREG?' command to see if that yields any better result. Like I mentioned above, 'AT+CREG' didn't work for me either.

                            The other AT command to see if the modem is actually connected or not is AT+COPS?.

                            If you get something like this: +COPS: 1,2,"22801",9 it means your modem is connected. If you get: +COPS: 0 it is not connected.

                            Thanks
                            Felix

                            GPIO translation table M5Stack / M5Core2
                            Information about various M5Stack products.
                            Code examples

                            cocoaC 2 Replies Last reply Reply Quote 0
                            • cocoaC
                              cocoa @felmue
                              last edited by

                              Hello @felmue,

                              An interesting fact:

                              • If I load the sample code you indicated the led of the modem continues to flash quickly without ever stopping , so it is correct to say that the modem is not connected .

                              • If I erase the flash with the executable and restart the Atom DTU the modem after a few seconds connects autonomously with the cellular network.

                              Therefore there is something in the source code of the http example that prevents the modem from connecting.

                              1 Reply Last reply Reply Quote 0
                              • cocoaC
                                cocoa @felmue
                                last edited by

                                Hello @felmue,

                                I think use AT+CREG? maybe it's not correct for NB-IoT connection on LTE technology.

                                Should the modem probably use AT+CEREG? .

                                What do you think? Should something be changed in TinyGSM?

                                Thx.

                                felmueF 1 Reply Last reply Reply Quote 0
                                • felmueF
                                  felmue @cocoa
                                  last edited by felmue

                                  Hello @cocoa

                                  actually I changed my fix to include sms only roaming state e.g. 7 like this:

                                  //        return (s == REG_OK_HOME || s == REG_OK_ROAMING || s == REG_OK_SMS);
        return (s == REG_OK_HOME || s == REG_OK_ROAMING || s == REG_OK_SMS || s == REG_OK_SMS_ROAMING);

                                  The reason for that is that it seems to be a valid state for NB-IoT.

                                  "7 Registered for "SMS only", roaming (applicable only when <Act>
                                  indicates NB-IOT"

                                  BTW: I've created a PR to that effect.

                                  Thanks
                                  Felix

                                  GPIO translation table M5Stack / M5Core2
                                  Information about various M5Stack products.
                                  Code examples

                                  cocoaC 1 Reply Last reply Reply Quote 0
                                  • cocoaC
                                    cocoa @felmue
                                    last edited by

                                    Hello @felmue ,

                                    I changed the header by inserting your change, but behavior uk the same of the previous on.

                                    I edited the file using CEREG instead of CREG.

                                    Something has changed but it is not yet possible to run the http example.

                                    11:51:23.983 > AT+CICCID
11:51:23.983 > 
11:51:23.983 > ERROR
11:51:23.983 > CCID: ERROR
11:51:23.983 > AT+CSQ
11:51:23.988 > 
11:51:23.989 > +CSQ: 24,0
11:51:23.989 > 
11:51:23.989 > OK
11:51:23.989 > Signal quality: 24
11:51:23.990 > Initializing modem...
11:51:23.990 > [  1689][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
11:51:23.996 > E (1581) gpio: gpio_set_level(227): GPIO output gpio_num error
11:51:24.297 > E (1882) gpio: gpio_set_level(227): GPIO output gpio_num error
11:51:29.297 > AT
11:51:29.300 > 
11:51:29.300 > OK
11:51:29.300 > ATE0
11:51:29.304 > 
11:51:29.304 > OK
11:51:29.304 > AT+CFUN=1
11:51:29.311 > 
11:51:29.312 > OK
11:51:29.312 > AT+QCLEDMODE=1
11:51:29.316 > 
11:51:29.316 > OK
11:51:29.317 > AT+CMEE=0
11:51:29.320 > 
11:51:29.321 > OK
11:51:29.321 > AT+CTZR=0
11:51:29.325 > 
11:51:29.325 > OK
11:51:29.325 > AT+CTZU=1
11:51:29.329 > 
11:51:29.329 > OK
11:51:29.329 > AT+CPIN?
11:51:29.335 > 
11:51:29.335 > +CPIN: READY
11:51:29.336 > 
11:51:29.337 > OK
11:51:29.337 > Waiting for network...
11:51:29.337 > AT+CEREG?
11:51:29.343 > 
11:51:29.343 > +CEREG: 0,5
11:51:29.344 > 
11:51:29.344 > OK
11:51:29.344 > success
11:51:29.344 > AT+IPADDR
11:51:29.352 > 
11:51:29.352 > +IP ERROR: Network not opened
11:51:29.355 > 
11:51:29.355 > ERROR
11:51:29.355 > Device IP address: 
11:51:29.355 > success
11:51:29.356 > Performing HTTP GET request... AT+CIPCLOSE=0
11:51:29.363 > 
11:51:29.364 > +CIPCLOSE: 0,4
11:51:29.365 > 
11:51:29.365 > ERROR
11:51:29.365 > AT+CIPRXGET=1
11:51:29.371 > 
11:51:29.371 > OK
11:51:29.371 > AT+CIPOPEN=0,"TCP","api.m5stack.com",80
11:51:29.382 > 
11:51:29.382 > +CIPOPEN: 0,2
11:51:29.383 > failed to connect
11:51:39.383 > Performing HTTP GET request... 
11:51:39.383 > ERROR
11:51:39.433 > AT+CIPCLOSE=0
11:51:39.440 > 
11:51:39.440 > +CIPCLOSE: 0,4
11:51:39.441 > 
11:51:39.441 > ERROR
11:51:39.442 > AT+CIPRXGET=1
11:51:39.447 > 
11:51:39.448 > OK
11:51:39.448 > AT+CIPOPEN=0,"TCP","api.m5stack.com",80
11:51:39.458 > 
11:51:39.458 > +CIPOPEN: 0,2
11:51:39.459 > failed to connect
11:51:49.460 > Performing HTTP GET request... 
11:51:49.461 > ERROR
11:51:49.510 > AT+CIPCLOSE=0
11:51:49.517 > 
11:51:49.518 > +CIPCLOSE: 0,4
11:51:49.518 > 
11:51:49.519 > ERROR
11:51:49.519 > AT+CIPRXGET=1
11:51:49.524 > 
11:51:49.524 > OK
11:51:49.525 > AT+CIPOPEN=0,"TCP","api.m5stack.com",80
11:51:49.535 > 
11:51:49.535 > +CIPOPEN: 0,2
11:51:49.536 > failed to connect
11:51:59.537 > Performing HTTP GET request...
                                    felmueF 1 Reply Last reply Reply Quote 0
                                    • felmueF
                                      felmue @cocoa
                                      last edited by

                                      Hello @cocoa

                                      if you want to use NB-IoT mode I found you'll need to un-comment the define in TinyGsmClientSIM7028.h line 32 as well.

                                      #define MODE_NB_IOT      //Comment this macro definition when using CAT mode

                                      BTW: CAT mode (e.g. not NB-IoT mode) works for me too.

                                      Thanks
                                      Felix

                                      GPIO translation table M5Stack / M5Core2
                                      Information about various M5Stack products.
                                      Code examples

                                      cocoaC 1 Reply Last reply Reply Quote 0
                                      • cocoaC
                                        cocoa @felmue
                                        last edited by cocoa

                                        @felmue It works in a totally random way, sometimes it gets the answer to the 'GET' and then it enters an infinite loop:

                                         AT+CIPRXGET=4,0
07:25:49.725 > 
07:25:49.727 > +CIPRXGET: 4,0,0
07:25:49.727 > 
07:25:49.727 > OK
07:25:49.727 > AT+CIPCLOSE?
07:25:49.734 > 
07:25:49.735 > +CIPCLOSE: 0,0
07:25:49.735 > 
07:25:49.735 > OK
07:25:50.219 > AT+CIPRXGET=4,0
07:25:50.226 > 
07:25:50.226 > +CIPRXGET: 4,0,0
07:25:50.227 > 
07:25:50.227 > OK
07:25:50.228 > AT+CIPCLOSE?
07:25:50.234 > 
07:25:50.234 > +CIPCLOSE: 0,0
07:25:50.236 > 
07:25:50.236 > OK
07:25:50.720 > AT+CIPRXGET=4,0
07:25:50.727 > 
07:25:50.728 > +CIPRXGET: 4,0,0
07:25:50.728 > 
07:25:50.728 > OK
07:25:50.728 > AT+CIPCLOSE?
07:25:50.736 > 
07:25:50.736 > +CIPCLOSE: 0,0
07:25:50.736 > 
07:25:50.737 > OK
07:25:51.221 > AT+CIPRXGET=4,0
07:25:51.229 > 
07:25:51.230 > +CIPRXGET: 4,0,0
07:25:51.230 > 
07:25:51.230 > OK
07:25:51.230 > AT+CIPCLOSE?
07:25:51.237 > 
07:25:51.237 > +CIPCLOSE: 0,0
07:25:51.238 > 
07:25:51.238 > OK
07:25:51.722 > AT+CIPRXGET=4,0
07:25:51.730 > 
07:25:51.731 > +CIPRXGET: 4,0,0

                                        However, the library must be modified to be able to obtain a communication as it does not connect with the original commands.
                                        I think the nb-iot command set in LTE is wrong.

                                        It is also my opinion that an nb-iot device without a hardware reset cannot be used seriously.

                                        Thanks for the helping.

                                        1 Reply Last reply Reply Quote 0
                                        • First post
                                          Last post