@christer

I have been using the Arduino IDE to create and compile and transfer code to my CoreS3.
Very simple.

There are lots if GutHub examples written ro this IDE.

Any one got the demo to log into the local wifi and turn off the AP??

firmware/data/config.json

this document has Wifi SSID and Password.

Any code Arduino or PlatformIO to load into CamS3 Unit to get it to stream RTSP on port 8554. it also needs to log into my home Wifi.
thanks

@christer

I have been using the Arduino IDE to create and compile and transfer code to my CoreS3.
Very simple.

There are lots if GutHub examples written ro this IDE.

Got a bit further in the quest.

I added the following:-
void setup() {
// Set console baud rate
SerialMon.begin(115200);
delay(10);

SerialAT.begin(115200, SERIAL_8N1, 18, 17, false);
delay(3000);
modem.restart();

and got some responses

23:06:21.706 -> [14189] Wait...
23:06:27.695 -> [20189] Trying baud rate 115200 ...
23:06:30.064 -> [22535] Modem responded at rate 115200
23:06:30.064 -> [22535] Initializing modem...
23:06:35.068 -> [27555] ### TinyGSM Version: 0.11.7
23:06:35.068 -> [27555] ### TinyGSM Compiled Module: TinyGsmClientSIM7600
23:06:45.272 -> [37756] Failed to restart modem, delaying 10s and retrying
23:06:45.272 -> [37756] Initializing modem...
23:06:55.486 -> [47957] Failed to restart modem, delaying 10s and retrying
23:06:55.486 -> [47957] Initializing modem...
23:07:03.779 -> [56269] ### TinyGSM Version: 0.11.7
23:07:03.779 -> [56269] ### TinyGSM Compiled Module: TinyGsmClientSIM7600
23:07:03.843 -> [56316] ### Modem: SIMCOM SIM7600G-H
23:07:03.843 -> [56316] ### Modem: SIMCOM SIM7600G-H
23:07:03.877 -> [56369] ### Modem: SIMCOM SIM7600G-H
23:07:03.877 -> [56369] Modem Name: SIMCOM SIM7600G-H
23:07:03.910 -> [56397] Modem Info: Manufacturer: SIMCOM INCORPORATED Model: SIMCOM_SIM7600G-H Revision: SIM7600G_V2.0.2 IMEI: "redacted" +GCAP: +CGSM
23:07:03.910 -> [56397] Waiting for network...
23:07:03.975 -> [56440] Network connected
23:07:03.975 -> [56440] Connecting to vsh.pp.ua
23:07:04.008 -> [56482] ... failed
23:07:04.008 -> [56482] Requesting current network time
23:07:04.008 -> [56484] Couldn't get network time, retrying in 15s.
23:07:18.986 -> [71484] Requesting current network time
23:07:19.025 -> [71486] Year: 2024 Month: 1 Day: 26
23:07:19.025 -> [71486] Hour: 23 Minute: 7 Second: 3
23:07:19.025 -> [71486] Timezone: 11.00
23:07:19.025 -> [71487] Retrieving time again as a string
23:07:19.025 -> [71506] Current Network Time: 24/01/26,23:07:18+44
23:07:19.185 -> [71672] Battery charge state: 0
23:07:19.185 -> [71672] Battery charge 'percent': 0
23:07:19.185 -> [71672] Battery voltage: 3.80
23:07:19.219 -> [71691] Chip temperature: 37.00
23:07:19.219 -> [71691] End of tests.

Thanks that did it.
I got a res: AT OK.

thanks.

I am trying to use TinyGSM
has any one got it working with he Core3 COM.X LTE?

but with no luck. get the following:-
22:44:52.276 -> [6988] Trying baud rate 115200 ...
22:45:02.304 -> [16999] Trying baud rate 57600 ...
22:45:12.314 -> [27009] Trying baud rate 38400 ...
22:45:22.312 -> [37019] Trying baud rate 19200 ...
22:45:32.324 -> [47029] Trying baud rate 9600 ...
22:45:42.325 -> [57039] Trying baud rate 74400 ...
22:45:52.334 -> [67049] Trying baud rate 74880 ...
22:46:02.336 -> [77059] Trying baud rate 14400 ...
22:46:12.356 -> [87069] Trying baud rate 28800 ...
22:46:22.358 -> [97079] Initializing modem...
22:46:32.393 -> [107111] Failed to restart modem, delaying 10s and retrying
22:46:32.393 -> [107111] Initializing modem...
22:46:42.440 -> [117143] Failed to restart modem, delaying 10s and retrying
22:46:42.440 -> [117143] Initializing modem...
22:46:52.451 -> [127175] Failed to restart modem, delaying 10s and retrying
22:46:52.454 -> [127175] Initializing modem...

Thanks

@felmue said in Connect COM.LTE to CoreS3?:

test

I give this a go. thanks

I have the M5CoreS3 and the Com.x LTE, not having any success communicating with the COM.X LTE. the dips are on the default 5/13.
what should they be set too? and is there any simple Example Test of LTE for me to test and follow??

I see this comment
"I suggest you set COM.LTE to use pins 16 / 17 and then use GPIO18 / 17 in your code. AFAIK PC_RX and PC_TX are the second serial."

not sure if just Dip 5 should change to 16 or 17?? help appreciated.

also in the Code is there a command to tell how to communicate with those different PINS??

first time use of the LTE.
thanks

I have a CoreS3 using UIFlow2 and set the TimeZone to GMT+11 (i am in Austrlai) time is 2145 but CoreS3 shows 23.45?? 2 hrs out Any one know why?