Hi folks
Is there any tutorial or example to send SMS via a COM.X LTE Module in UIFlow or Python
I have a SIM card of TalkTalk with deactivated PIN code.
But I have no luck to get it to work.
Thank you for your help.
Best regards
Thomas

M5StickFreakler
@M5StickFreakler
Posts made by M5StickFreakler
-
COM.X LTE (4G) Module Example UIFLOW/Phython
-
RE: TF sensor get always the same value
I have no clue why this happens. Does no one use the TF-sensor for such "long" time without restart?
-
RE: TF sensor get always the same value
New findings:
The TF-sensor readings "hangs" exactly after 13 days.
After that always the same value is given out.
This behavior was occured every 13 days in the last 5 months.
Very strange.
What could that be? -
TF sensor get always the same value
Hi folks
I have a program that reads the TF sensor every second.
After 1 or 2 weeks, the sensor suddenly only delivers the same constant value (last value read from it).
I have to restart the whole device and then the sensor does read out correct current values again for 1 or 2 weeks.example (values only to visualize with some fault measurement like in real):
99.7, 99.6, 99.7, 98.9, 98.8, 98.5, 98.3, 98.4, 98.3, 97.9, 97.6, 97.2, 97.3, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7, 96.7Does anyone know the problem?
Best regards
Thomas -
RE: [Solved] https request ends in error 12: "ENOMEM"
It works with Firmware V1.5.1 and above
-
RE: [Solved] GPS Unit (AT6558)
@m5stack said in GPS Unit (AT6558):
start takes time, (maybe 3~5min). the signal quality very important , so had better use it in the house outside.
Thank you very much.
Unfortunately it does not work with any port as I have described above.
I just receive Quality "NO signal". It can stay for hours outside, nothing changes.
Cold start time is 35 seconds as you can see in technical details of m5stack.BUT HERE IS THE BEST:
I received today 4 new GPS Units and now it works.
My "old" two GPS units are not working.
That was it. A lot of waited time -
RE: [Solved] Pb.Hub and Pa.Hub grayed out?
@skink said in Pb.Hub and Pa.Hub grayed out?:
Start the Desktop IDE Version (Offline Version) of UIFlow, then go to "CheckUpdate" there you start the update to the new version 1.0.9.1 then Pb.HUB and Pa.HUB are activated again and you can access them !
You may have to install the software completely again !?greetings skink
Hi skink
This was my mistake.
I have already the newest version of UI-Flow installed but I didn't realized, that I have to change the Version via the following button too:
So I have switched to V1.5.1 and now the pa.Hub and Pb.Hub aren't grayed out.
Too dumb of me.Thank you and best regards
Thomas -
RE: [Solved] GPS Unit (AT6558)
@world101 said in GPS Unit (AT6558):
Hint: if you use the forum search feature you can find threads like this that say the M5Stack Fire PSRAM conflicts with port C because they use the same GPIO 16 and 17, which is also the same ports the GPS units and modules use (see the GPS docs). The work around involves cutting a trace and rewiring.
Thank you
But I would like to get a solution from M5Stack withouth cutting wires in all my devices.
M5Stack sell this GPS units to use 'em on M5Stack devices and does not provide any information that we have to modify the hardware to get running it.
Also I do not use the GPS Modul, but I use the GPS Unit!@m5stack could you provide customers with any official information about the behavior?
Best regards
Thomas -
RE: [Solved] Pb.Hub and Pa.Hub grayed out?
@m5stack said in Pb.Hub and Pa.Hub grayed out?:
@m5stickfreakler you could select the 1.5.1 (beta) version in the navigation. then will solve this problem
Hi
I have installed Firmware 1.5.1 on my M5Stack Fire devices.
The problem ist not the firmware, but the Desktop UIFlow Version 1.0.9.1.
That has nothing to do with the firmware Version of the device.
Or do I something missunderstand?Best regards
Thomas -
[Solved] Pb.Hub and Pa.Hub grayed out?
Hi folks
With newest UIFlow Desktop Software V 1.0.9.1 the Units Pb.Hub and Pa.Hub are grayed out.
I have buyed it some weeks ago and now it is not supported anymore?
Why????
Do I something wrong?
Best regards
Thomas