STAMP CATM does not respond (Solved, HTML Get and Send Email)

HappyUser

Hi,
I have my STAMP CATM connected to my M5StickC : GND to GND , +5 Out to 5V, G36 to RX and G26 to TX.
Then :
Serial2.begin(115200, SERIAL_8N1, RXD2, TXD2);
delay(300);
Serial2.println("ATI\r\n");
Read_Response(5000); // Serial2 read into Receive_buffer
Serial.println(Receive_buffer);

But when reading out the Serial2 I get no response at all.
Any idea?
Thanks

ajb2k3

have you got a sim in it?

HappyUser

Thank you for your reply
SIM card is placed according to picture.
In the mean time I have tried different scenarios with :
//Serial1.begin(115200, SERIAL_8N1, RXD2, TXD2);
Serial1.begin(115200, SERIAL_8N1, 26, 0);
//Serial1.begin(115200, SERIAL_8N1, 0, 26);

This is based on the following link in which also problems with Serial are mentioned : https://community.m5stack.com/topic/1521/serial2-on-m5stickc/5

This link appears to provide working serial to serial communication: https://gist.github.com/dj1711572002/0ad8aa8aee618e5f2b7bfa719bc2b736

But no luck for me.
I hope anyone got this working.
Regards

HappyUser

Well,
Finally found it :
This is works : Serial1.begin(115200, SERIAL_8N1, 0, 26); // SIM7080G
and G26 connected to TX and G0 to RX.
Now trying to get the modem responding to SIM7080G commands.

ajb2k3

I’ve got one on my desk but haven’t purchased a sim for it yet

HappyUser

@happyuser
A few tips who want to start with this module:
1] Remove PIN code, makes life much easier
2] Download the application notes for this module. Both the complete AT instruction set and the note on HTTP application. This document provides clear instructions how to use HTTP, GET, POST etc
3] I experienced ERROR response on SHCONF command. Googled around, saw numerous hits. It appears that switching off and on power does the trick for me. I did not see a reset AT instruction
4] I got it all working with these instructions :
Serial.println("Begin..");
//pinMode(RXD2, INPUT);
//pinMode(TXD2, OUTPUT);
//showLog("Reset Module...");
//SIM7020
//DTU.Init(&Serial1,36, 26);
//Serial1.begin(115200, SERIAL_8N1, RXD2, TXD2);
//Serial1.begin(115200, SERIAL_8N1, 26, 0);
Serial1.begin(115200, SERIAL_8N1, 0, 26); // SIM7080G

delay(300);
//Serial1.print("ATI\r\n");
//Serial1.println("AT+CSQ\r\n");
//Serial1.println("AT+IPR?\r\n");
Serial1.print("ATZ\r\n");  // Reset to default
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+IPR=115200\r\n");  // Reset to default
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CCLK?\r\n");  // Reset to default
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+SHSSL=1,\"\"\r\n");  // Reset to default
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);



Serial1.print("AT+CFUN=1\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CMGF=1\r\n");  // text mode
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

// Om http te testen

Serial1.print("AT+CFUN=0\r\n");  // Disable RF
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

//Serial1.print("AT+CGDCONT=1,\"IP\",\"internet\",,0,0\r\n");  // 
Serial1.print("AT+CGDCONT=1,\"IP\",\"internet\"\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CFUN=1\r\n");  // Enable RF
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+CGATT?\r\n");  // Check PS Service
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CGNAPN\r\n");  // Query the APN service
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+CNCFGN=0,1,\"internet\",,0,0\r\n");  // Before activation please
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+CNACT=0,1\r\n");  // Activate
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);



Serial1.print("AT+CNACT?\r\n");  // Query the APN service
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);



Serial1.print("AT+SHCPARA\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SHCONF=?\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SHCONF?\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

// Serial1.print("AT+SHCONF="URL","https://api.thingspeak.com/update"\r\n"); // Query the APN service
//Serial1.print("AT+SHCONF="URL","httpbin.org"\r\n"); // Query the APN service
//Serial1.print("AT+SHCONF="URL","http://34.193.132.77"\r\n"); // Query the APN service

//SIM7600_Error=1;
//for (int i=0;i<10;i++)
  // {
      //Serial1.print("AT+SHCONF=\"URL\",\"http://www.google.com\"\r\n");  // Query the APN service
      Serial1.print("AT+SHCONF=\"URL\",\"http://www.httpbin.org\"\r\n");  // Query the APN service

      delay(10);
      Read_Response(5000);
      Serial.println(Receive_buffer);
      delay(2000);
   //   if (SIM7600_Error=0) {break;}
  // }
     


Serial1.print("AT+SHCONF=\"BODYLEN\",1024\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SHCONF=\"HEADERLEN\",350\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);



Serial1.print("AT+SHCONN\r\n");  // Query the APN service
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SHSTATE?\r\n");  // Query the APN service
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SHCHEAD\r\n");  // Query the APN service
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SHAHEAD=\"User-Agent\",\"curl/7.47.0\"\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);    

Serial1.print("AT+SHAHEAD=\"Cache-control\",\"no-cache\"\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500); 

Serial1.print("AT+SHAHEAD=\"Connection\",\"keep-alive\"\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500); 

Serial1.print("AT+SHAHEAD=\"Accept\",\"*/*\"\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500); 


    
Serial1.print("AT+SHREQ=\"/get?user=jack&password=123\",1\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500); 


Serial1.print("AT+SHREAD=0,391\r\n");  // 
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

HappyUser

Okay, Had a lot of <bad language> getting sending email working.
Than I realized that powering the module straight from the M5StickC appeared to causes glitches. I have placed a capacitor on top of the 5Volt to the module and now I am able to send emails also. For those that are interested, here is the code (with a lot of overhead no doubt, that works for me ):
Serial1.begin(115200, SERIAL_8N1, 0, 26); // SIM7080G

delay(300);
//Serial1.print("ATI\r\n");
//Serial1.println("AT+CSQ\r\n");
//Serial1.println("AT+IPR?\r\n");
Serial1.print("ATZ\r\n");  // Reset to default
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CREBOOT\r\n");  // Reset to default
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

/*
Serial1.print("AT+CMEE=2\r\n"); // Verbose error printing ??
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);
*/

Serial1.print("AT+IPR=115200\r\n");  // SetTE-TAFixedLocalRate
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CCLK?\r\n");  // Clock
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

// Upload a file

Serial1.print("AT+CFSINIT\r\n");  // Clock
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

String Command_Str;
Command_Str="AT+CFSWFILE=0,"0001.txt",0,";
Command_Str=Command_Str+FileSize;
Command_Str=Command_Str+",10000\r\n";
Serial.println(Command_Str);

Serial1.print(Command_Str); 
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);  

for (int i=0;i<FileSize;i++) {Serial1.print(jpg_small[i]);}


Serial1.print("AT+CFSGFIS=0,\"0001.txt\"\r\n");  // 
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);   


Serial1.print("AT+CPIN?\r\n");  // Ccheck SIM
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);  

Serial1.print("AT+CSQ\r\n");  // Check signal
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);  


Serial1.print("AT+CFUN=0\r\n");  // Set Phone Functionality isable RF
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

//Serial1.print("AT+CGDCONT=1,\"IP\",\"internet\",,0,0\r\n");  // 
Serial1.print("AT+CGDCONT=1,\"IP\",\"internet\"\r\n");  //  Define PDP Context
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CFUN=1\r\n");  // Set Phone Functionality Enable RF
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+CGATT?\r\n");  // Attach or detach from GPRS service
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+CGNAPN\r\n");  // Get Network APN in CAT-M or NB-IOT Query the APN service
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+CNCFGN=0,1,\"internet\",,0,0\r\n");  // Before activation please
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+CNACT=0,1\r\n");  // APP Network Active Activate
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);



Serial1.print("AT+CNACT?\r\n");  // APP Network Active Activate Query the APN service
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+EMAILCID=0\r\n");  // Set parameters of email
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+EMAILTO=30\r\n");  // Set parameters of email time out
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

/*
Serial1.print("AT+EMAILSSL=2,0,"email.cer","email.pem"\r\n"); // Set Encrypted mail
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);
*/
// https://randomnerdtutorials.com/esp32-send-email-smtp-server-arduino-ide/

Serial1.print("AT+SMTPSRV=\"smtp-mail.outlook.com\",587\r\n");  // Set SMTP server
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

//SMTP Password: (you need to use a Google App Password, not your Gmail password!)
//https://support.google.com/accounts/answer/185833
// https://www.hesk.com/knowledgebase/index.php?article=72

Serial1.print("AT+SMTPAUTH=1,\"my.email.com\",\"myApppassword\"\r\n");  // Set username and password

delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SMTPCS=\"ASCII\"\r\n");  // Set Email SSL function
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+EMAILSSL?\r\n");  // Read Email SSL function
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+EMAILSSL=2,0,\"\",\"\"\r\n");  // Set Email SSL function
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+EMAILSSL?\r\n");  // Read Email SSL function
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

Serial1.print("AT+SMTPFROM=\"my.email@outlook.com\",\"Fakename\"\r\n");  // Set username and password

delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);
     
Serial1.print("AT+SMTPRCPT=0,0,\"Sendto@mac.com\",\"john\"\r\n");  // Set recipient To:
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);


Serial1.print("AT+SMTPSUB=\"Test4\"\r\n");  // Set recipient Bcc:
delay(10);
Read_Response_OK(5000);
Serial.println(Receive_buffer);
delay(500);

String Email_Body="This is a new Email";
int Body_size;
Body_size=Email_Body.length();
Serial.print("Body size is :");
Serial.println(Body_size);

Serial1.print("AT+SMTPBODY=19\r\n");  // Set recipient Bcc:
delay(10);
Read_Response_OK(5000);
//Serial.println(Receive_buffer);
//delay(500); 

Serial1.print(Email_Body);
//Serial1.print("\r\n");
delay(10);
Read_Response(5000);
Serial.println(Receive_buffer);
delay(500);

char ccc;
Serial.println("AT+SMTPSEND");
Serial1.print("AT+SMTPSEND\r\n"); //
delay(10);
while (Serial1.available())
{
ccc=Serial1.read();
Serial.print(ccc);
}

/*
Read_Response(5000); //Geen OK
Serial.println(Receive_buffer);
delay(500);
*/
Serial.println("And we are done");
while (1) {delay(300);}

ajb2k3

Thanks for this, I haven't started on mine as still looking through IOT services