Unit V2 Connection

  • Same problem for me as well. I submitted my post regarding the same issue yesterday. Waiting to hear from M5 on debugging / fixing it

  • @m5stack
    I installed the driver and unitv2.py works on browser.,
    but I can't find UnitV2's SSID on WiFi (SSID: M5UV2_XXX)
    How do I fint it ? I want to use UnitV2 on arduino with UART,
    without PC.

  • I have the same problem with the AP.

    PS: There are now 3 threads and no answer :(

  • unitv2% ip a
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet scope host lo
    valid_lft forever preferred_lft forever
    2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:30:1b:ba:02:db brd ff:ff:ff:ff:ff:ff
    inet brd scope global eth0
    valid_lft forever preferred_lft forever
    3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq qlen 1000
    link/ether 00:e0:4c:05:22:59 brd ff:ff:ff:ff:ff:ff
    4: wlan1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq qlen 1000
    link/ether 02:e0:4c:05:22:59 brd ff:ff:ff:ff:ff:ff
    inet brd scope global wlan1
    valid_lft forever preferred_lft forever

  • hello same problem.. no wifi AP, updated firmware no change...
    USB drivers seems not working on my OSX 10.14.6
    so its quite useless for now :(

    Update: I figured out how to get LAN up and running
    removed SR9900Composite.kext SR9900.kext from /Library/Extensions/ and now Lan works (so its working without driver... and with driver its not working)

  • This post is deleted!

  • Hi, the new firmware still doesn't show any APs for me, even if I only connect it to USB-C from the charger. Does it switch to AP mode somewhere?

  • Same on my machine :( no AP at all....

  • sorry, the firmware seems still to have some bug. we are positioning the issues now.

  • @m5stack Any update on this? I've been waiting to get my hands on the device due to its wifi capabilities yet unable to get SSID?

  • Hello, @m5stack any update on the firmware?

  • What is happening with this its so disapointing months on from preorder i still cant even connect to the unit.

  • I couldn't even connect over USB and I emailed them about it, they suggested to restart the network interface. At first this didn't seem to work, but I think I just didn't wait long enough. So what now works for me is just bringing the network interface down, bringing it up again and waiting a couple of seconds:

    $ sudo ip link set enx00e0993168d7 down
    $ sudo ip link set enx00e0993168d7 up
    $ ip a show dev enx00e0993168d7
    13: enx00e0993168d7: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
        link/ether 00:e0:99:31:68:d7 brd ff:ff:ff:ff:ff:ff
        inet brd scope global dynamic noprefixroute enx00e0993168d7
           valid_lft 42632sec preferred_lft 42632sec
        inet6 fe80::9c4a:2259:c022:588/64 scope link noprefixroute
           valid_lft forever preferred_lft forever

    After this, I can access the web interface and ssh on over USB. Wi-Fi doesn't seem to work and I didn't look at it because the USB network is fine for me for now.

  • @m5stack Why is this link dead?