I read on stack overflow you need to use a 3rd party library for this : WolfSSL Link to Stack Overflow

I used an antenna analyzer and this is what I got: [image: 1583919274876-lorawan_internal_antenna-resized.jpg] There are 3 spikes around the following frequencies: 610 MHz 820 MHz 2300 MHz

@skink and @ajb2k3 Thanks for your great help, this is a good solution. I think I have to use 3,7V and not 5V because it is battery pack input.

I looked around for some examples for this too but so far have found none, here is the datasheet if it helps https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/docs/datasheet/module/MAX3421E_en.pdf

@m5stack as well as 485 lol

Ok so it seems that Vlc will never be able to decode the http stream as it's not really a stream just consecutive jpeg images. So I turned to rtsp instead and the micro-rtsp project. I used the instructions here mgo-tech.com, to install Arduino IDE and ESP plugin (translated by google), take care to use correct pin mapping, I used that instruction as it is for M5Camera type b the same as I have. Tried the CameraWebServer also, much nicer then the original software. Followed instructions here hackster.io to get a http/rtsp server. Worked fine except the picture was the wrong way around for my application so I copied a few lines from the CamereaWebServer example to flip it vertical and Horisontal and lowered resolution to vga. Works fine with Vlc but a bit more sensetive to fast movement then the http stream. Why may you ask? Vlc got recording and is easily implemented in my project.

Have you tried erasing the flash, and reflashing a different firmware? Did you use the firmware burner in uiflow desktop to burn the firmware?

Hello Sam, I have the Lora868 module; Just a quick word of advice, if you want to use the module with the LMIC library then you -as mentioned in the article you pointed out to- have to solder the DI0 1 pad of the RA-01 to pin 34 of the M5stack connector. The pin-out for the Lora868 module: MISO - 19 MOSI - 23 SCK - 18 NSS - 05 RESET - 26 DIO 0 - 36 DIO 1 - 34 <-- this one is NOT connected when you get your Lora868 module, soldering needed! If you want to know the physical pinout of the RA-01 (https://docs.ai-thinker.com/_detail/lora/spec/ra-01_picture.png?id=lora) Greetings!

The encoder signal is displayed very accurately and also evaluated very precisely. Of course also with the NXT motors and EV3 motors. I will see that I make a video the days once again where you can see how precisely he drives the set values. @liemph I will then connect a NXT motor and run it on different values of the encoder! The GlideWheel PF and RCX motor controller for NXT or EV3 cannot be mounted directly on the old motors, because it is designed for the power motors (on these it is mounted with two pins), but you can mount it somewhere in the system on the shaft of the motor. So you can make an encoder motor out of any Lego motor.

@mmroos said in M5Stack Fire and M5 Piano?: So I ordered a M5stack Fire and a M5 Piano. Now I found out that the Piano's 15 pin connector cannot fit anywhere on my M5Stack. Is there a way to convert grove to those 15 pins or is there another solution? Preferably one where I do not have to sacrifice my 600ah battery. The Keyboard is designed for the I/O Base plate https://m5stack.com/collections/m5-base/products/battery-bottom-150mah?ref=pfpqkvphmgr [image: BOOTOM_1200x1200.jpg?v=1566377177] Here is the know information on the keyboard.link text The pins can be found on the internal 2X15 pin internal bus connection.

@ajb2k3 said in Is it possible to dock M5Stack Fire to FACES ?: There shouldn't be any problems using the fire on the Faces base as it is still a core. Yep there is no problem at all. I have fire and ita fine with face. Now i have also new face bottom with just arrive. So clasic face finally got 2 extra ports.

I tested the DAC module. You need to use dac0.writeData (Volt, save = True) in the range from 0 to 2700 to get from 0 to 3.3V. For variable indications to be similar to voltage, they should be divided by 0.00125.[image: 1576164901150-dac-resized.png]

It will help a lot if M5STACK can publish more sample code in sms/mqtt communication.

@arquimedes said in conexion i2c: ¿Donde puedo comprar un cable de conexión para el puerto I2C?, la separación entre pines de 2 mm. es dificil de encontrar, y los módulos que tengo, el GRAY y el FIRE no los traen Los cables se conocen como cables de ranura y están disponibles en múltiples ubicaciones. Las conexiones son difíciles de rastrear porque son propietarias, sin embargo, puede comprar las conexiones montadas en PCB desde este enlace en la tienda M5Stack. M5Stack conexiones

Got it! Thanks!

@Thrashe yes, there is a new firmware 4.0.68 specific for stickV that works and has the logo etc.