would be great to have a m5f file repository somewhere

DR_Froggy_rD
@DR_Froggy_rD
3d printing hobbyist actively designing stuff.. I own a prusa mini and an easythreed x7I owned a micro3d plus printer which is dead now.. (sadface) cannot make it work again... I have a velleman K8200...
I have a Ph D in science and I am a martial artist. I survived a health accident and I am almost back to normal.
I wad looking for a solution to A) read the extruder motor input of the prusa mini to run another extruder. as a direct drive instead. I have bought an extra extruder from easythreed in order to do that at some point and B) I want to tune my printer using instant shaping: for that I need a accelerometer that can measure vibration of the printer: therefore M5 stack coimes probably as a good idea...
Posts made by DR_Froggy_rD
-
RE: adding a repository of simple projects that one can easily swap the core type to be dlded directly into uiflow
-
adding a repository of simple projects that one can easily swap the core type to be dlded directly into uiflow
I would like to import directly project into uiflow to start ftom a blockly example
-
RE: How to flash tasmona or anything to M5Stack ATOM Lite using esptool?
I have alsoo a problem with esptool
.
.
.
.
.
.
.
.
Traceback (most recent call last):
File "esptool\cmds.py", line 94, in detect_chip
File "esptool\loader.py", line 378, in check_command
File "esptool\loader.py", line 347, in command
File "esptool\loader.py", line 279, in read
File "esptool\loader.py", line 1387, in slip_reader
esptool.util.FatalError: Serial data stream stopped: Possible serial noise or corruption.During handling of the above exception, another exception occurred:
Traceback (most recent call last):
File "esptool.py", line 34, in <module>
File "esptool_init_.py", line 995, in main
File "esptool_init.py", line 637, in main
File "esptool_init_.py", line 880, in get_default_connected_device
File "esptool\cmds.py", line 121, in detect_chip
File "esptool\loader.py", line 603, in connect
File "esptool\loader.py", line 544, in _connect_attempt
File "esptool\loader.py", line 407, in sync
File "esptool\loader.py", line 323, in command
File "serial\serialutil.py", line 372, in timeout
File "serial\serialwin32.py", line 222, in _reconfigure_port
serial.serialutil.SerialException: Cannot configure port, something went wrong. Original message: PermissionError(13, 'A device attached to the system is not functioning.', None, 31)
[6352] Failed to execute script 'esptool' due to unhandled exception!before clicking the burn button on m5burner, I push the button to enter boot mode green led is flashing
-
RE: help needed to get started.
thx Adam....As you said I found it..I still do not know why it is not workimg with atom s3
voila -
RE: help needed to get started.
Ok thks adam.
By the way i have a m5stick cplus. I could burn uiflow on it.
Does it mean then i can install any program made with uiflow on it?without needing to install the program via m5burner?from uiflow.
I am looking for the key of each part cannot find those i have the sn feom the label ...
By the way i printed the part yesterday and i neede to scale it a bit to fit the tailbat and a m5atom s3. Thank you for that you saved me time also i had to print it 3 times before getting the right dimensions.
It may be due to my printer tolerances! I will send you the dimension i used. ByeFrog
-
RE: help needed to get started.
Hi Adam, so: I unzip my file in programm subfolder.
open M5nurner .exe as administrator.I can update firmware list.... but still looking for the same patch in the unzipped folder: I have anotherjavascript error message:: It is not EPERM but ENOENT..
However I connected the s3 to it. and push the left side button until green led flashes....then connect com6 (the detected port com there it is green) It fails to erase or to burn. failed to get mac. also when reducing the baud rate to 11000..
I tried even the easyloader software without success... -
RE: Members Introductions aka The Icebreaker discussion.
I found you and let you a comment on your atom choacker building block