🤖Have you ever tried Chat.M5Stack.com before asking??😎

Categories

  • Firmware updates, Hardware Revisions, New Product info can be found here.

    75
    Topics
    821
    Posts

    S

    @Mati said in UIFlow 1.8.4:

    @m5stack said in UIFlow 1.8.4:

    We are very sorry, we are working hard to supplement the support of related modules

    thx for reply, maybe all will be happy if we can see some roadmap with HW implementation.

    “Good point, Mati. A roadmap would definitely help everyone plan projects better. I’m also waiting on Zigbee support!”

  • M5Stack Events

    Review Campaign
    7
    Topics
    27
    Posts

    konacurrentsK

    I’ve built a great extensible architecture with M5 and basically any sensor. It was mentioned in my reply
    https://community.m5stack.com/post/29410

    It’s one thing to capture some data, it’s another to do the same in a scalable collective user base. That requires a distributed collection and messaging environment. Sensing and Controlling are two major branches of that challenge.

    So I think this community challenge needs to think bigger than a few M5 devices. 😄

  • Wish for a feature that doesn't exist yet? this is the place to ask for it. we will collect all the requirements and enquiry's and who knows ... sometime wish might come true!

    208
    Topics
    653
    Posts

    Yan YeziY

    I hope M5Stack StamPLC internal firmware support OTA update,like M5VAMeter.Use M5burner to update firmware is hard.

  • Forum rules - Announcements - General chit chat (ESP-32, ESP-8266, IoT, Raspberry Pi etc...)

    Anouncements Forum Rules (!!!!READ THIS FIRST BEFORE POSTING!!!!) News and Blog posts
    914
    Topics
    2.9k
    Posts

    K

    Just tested another release of UiFlow (version 2.3.3) for the Tab5... Unfortunately, I am seeing the same results that I saw with Version 2.3.2... -16Kpa without any air tubes connected to the M5Stack Air Tube sensor... Along with the i2c driver install error...

    Hopefully M5Stack Team is getting close to resolving the issue... I was planning to use the Tab5 project I was working on for the M5stack Innovation contest but it looks like that will not happen due to the issues I am running into with finding an air tube sensor that will accurately work with the Tab5... Oh well... Hopefully the M5stack team will release an upgraded Air Tube sensor soon that will easily work with the Tab5... Until then, I will keep searching for a solution....

  • Core and Modules info.

    Modules FAQS Units Cores Bases Atom
    3.3k
    Topics
    13.3k
    Posts

    K

    Yes, it is the display's problem. Its flex cable might be damaged.

  • Projects Sharing.

    430
    Topics
    1.7k
    Posts

    M

    https://macsbug.wordpress.com/2025/08/14/m5stack-fm-radio/
    I created an FM radio using M5Stack and SI4732 DSP.
    The receiver is similar to the ATS mini (encoder operation).
    It is operated with three buttons.

    M5_ant_480s.png

    M5_antL_480s.png

  • This is the place to discuss driver issues, M5 burner troubleshooting, and development of software compatible with M5Stack

    Squareline Studio / LVGL UIFlow Arduino Micropython M5EZ ESP - IDF UiFlow 2.0
    2.4k
    Topics
    9.3k
    Posts

    C

    @csierra67 Further to this suggestion, I tried the mpy route but got an error, type mismatch and the device frozen during upload needed to be burned again to recover control
    Finally I tried to not set the time and work with the Time section rather than the RTC section with the assumption that the device being connected to Internet anyway, it would get the correct time by itself.
    The following example works flawlessly and closes my issue as a reference for fuuture developperssolution.jpg

  • 228
    Topics
    513
    Posts

    M

    https://macsbug.wordpress.com/2025/08/14/m5stack-fm-radio/
    M5Stack と SI4732 DSP で FM Radio を製作しました。
    ATS mini (Encoder操作) に似た受信機です。
    操作は ３つのボタンで 行います。

    M5_ant_480s.png

    M5_antL_480s.png